← Repair Guides

✦ Battery

How to Replace a MacBook Pro 13-Inch M1 Battery (A2338): Step-by-Step Guide

How to Replace a MacBook Pro 13-Inch M1 Battery (A2338): Step-by-Step Guide
Repair Guide

MacBook Pro 13-Inch M1 Battery Replacement

Your M1 MacBook Pro still has plenty of speed left. If the battery is the only thing holding it back, here is how to give it a fresh one.

The 13-inch MacBook Pro with M1 (model A2338) is one of the best laptops Apple ever made, and its battery is the part most likely to wear out first. The battery is glued in, so this is a patient, careful job, not a quick one. Set aside an afternoon and follow along.

DifficultyModerate
Time1 to 2 hours
BatteryA2171, $84.99
Hardest partGlued cells

Is this the right guide for your MacBook?

Flip your MacBook over and read the small print near the hinge. If it says A2338, you are in the right place. The same A2171 battery is also listed for the A2289 (2020, Intel, two Thunderbolt ports) and the A2159 (2019), but the internals around it differ, so use a guide for your exact model. Not sure which one you have? Our MacBook model number guide takes 30 seconds.

What you need

  • The battery: A2171 battery for A2338
  • Screwdrivers: P5 pentalobe and T5 Torx. Our 12-in-1 MacBook screwdriver set has long-reach pentalobe and Torx bits made for this.
  • Opening tools: suction handle, plastic opening picks, a spudger, tweezers and a few plastic cards.
  • Adhesive remover made for electronics, plus nitrile gloves and safety glasses.
  • A magnetic mat or labeled cups. There are a lot of small screws in this job.
Battery safety. Run the battery down as low as you can before you start. A charged lithium battery that gets punctured can start a fire that is very hard to put out. Never use metal tools to pry the cells, and stop if a cell looks swollen. Adhesive removers are flammable and can irritate skin and eyes, so work in a ventilated room away from flames, and keep the remover off the screen and plastic parts.

Step-by-step: A2338 battery replacement

1
Shut down and remove the bottom case screws

Shut the Mac down and unplug it. Remove the six P5 pentalobe screws from the bottom case. They come in three lengths, so lay them out in the same pattern you found them.

2
Pop the bottom case off

Press a suction handle near the front center of the bottom case and lift just enough to slip a pick in. Run the pick along the front and sides to release the clips, then slide the case off toward the front of the laptop. It does not lift straight up.

3
Disconnect the battery

Peel back the tape over the battery connector area. Flip up the small locking flap on the battery data cable connector and slide the cable out. Remove the T5 Torx screw holding the battery power connector and lift the connector so it cannot touch its socket. Do this before anything else.

4
Remove the trackpad

The trackpad sits over part of the battery. Remove its cable bracket, disconnect the trackpad cable, then warm the cable gently and peel it off the battery. Remove the trackpad screws and lift the trackpad out, keeping track of the small washers under it.

5
Free the battery board

Remove the two T5 screws holding the small battery board and tilt it up out of the way.

6
Release the battery adhesive

Put a few drops of adhesive remover under the edge of one cell, wait two to three minutes, then slide a plastic card under the cell and lift slowly. Do the outer cells first and the center cell last, since it takes longest to release. If a cell resists, add more remover and wait. Never bend or force a cell.

7
Prepare and dry test the new battery

Compare the new battery to the old one and move over the data cable if your new battery does not have one fitted. Before you remove any adhesive liners, connect the power and data cables and press the power button. Open System Settings, then Battery, and confirm macOS sees the battery and it is charging. Shut down and disconnect again. Our parts terms require this dry test before final install.

8
Install and reassemble

Clean off old adhesive, peel the liners from the new battery, set it in place and press each cell down. Refit the battery board, then the trackpad. Start every trackpad screw finger-tight, check the trackpad sits centered, then tighten. Reconnect the trackpad cable and the battery, retape the connectors and slide the bottom case on from the hinge side before pressing the clips down.

9
Calibrate the new battery

Charge to 100% and leave it plugged in for at least two more hours. Use it on battery until you get the low battery warning, let it go to sleep, leave it for about five hours, then charge it back to 100% without interruption.

Want photos? Keep Apple's official manual or iFixit's A2338 battery guide open while you work.

Which MacBook batteries fit?

Your model Battery Price
MacBook Pro 13" M1 (A2338) A2171 $84.99
MacBook Pro 13" 2020, two ports (A2289) A2171 $84.99
MacBook Pro 13" 2019 (A2159) A2171 $84.99
MacBook Pro 13" 2016 to 2017 (A1708) A1713 $84.99
MacBook Air 13" 2018 to 2020 (A1932, A2179) A1965 $89.99
MacBook Pro 13 A2338 A2171 replacement battery
A2338 Battery (A2171)$84.99 · zero cyclesShop →
MacBook Pro 13 A2289 replacement battery
A2289 Battery (A2171)$84.99Shop →
12 in 1 MacBook screwdriver set
MacBook Screwdriver Set$24.99 · pentalobe and TorxShop →

See every laptop battery in battery parts.

Glued batteries not your thing?

Totally fair. Send your MacBook to Strictli and our Strictli Certified technicians will do the battery swap for you.

Start a mail-in repair

FAQ

When should I replace my MacBook Pro battery?

Check System Settings, then Battery. If macOS shows Service Recommended, or the laptop no longer gets through your normal day, it is time.

Is the M1 and M2 13-inch MacBook Pro battery the same?

Both use the A2338 model number. Our listing shows the A2171 battery for the M1 A2338; check the compatibility line on the product page before ordering for an M2.

Can I use isopropyl alcohol instead of adhesive remover?

Some people do, but MacBook battery adhesive is strong and a remover made for electronics works faster and with less prying. Less prying means less risk to the cells.

How long does a MacBook battery replacement take?

Most first-timers take one to two hours. Waiting on the adhesive is most of it.

Prices and stock as of November 12, 2026. Repairs you perform are at your own risk; see our parts purchasing terms for warranty details.

More from Repair Guides